Navigation and fishing electronics, installed in Wilmington, NC
Kane Marine Systems installs navigation and fishing electronics on boats across New Hanover County, from a single new chartplotter to a full helm of displays, radar, sonar and autopilot. Bill Kane comes to the boat, plans the layout with you, runs the wiring and the NMEA 2000 network properly, and sets everything up before he leaves.
When it is time for new electronics
- The chartplotter is slow, the chart is years out of date, or the screen is hard to read in sun.
- You have gauges, a plotter and a fishfinder that each show something different.
- The dash has a mix of old holes, dead switches and gear from three owners ago.
- You want radar, AIS or an autopilot and nobody has told you what the boat can take.
- You bought a new display and the box is still in the garage.
- The trim tabs, switches or lighting work sometimes.
How an install goes
Navigation and Fishing Electronics on a boat comes down to the jobs below, all of them done at the dock by Bill.
-
Plan it on the boat
What you run, how you fish or cruise, and what the helm can physically hold all shape the layout. Bill looks at the dash, the power, the transducer options and the existing network before anything is ordered.
-
Wire it to last
Tinned marine wire, proper fusing, labeled runs, sealed connections and a clean NMEA 2000 backbone. Most electronics failures on the water are wiring and connections, so that is where the care goes.
-
Set it up and hand it over
Charts loaded, sonar tuned to your transducer, radar overlaid, engine data on screen, and a walk-through at the helm so you know what every page does before you leave the dock.
Ask about navigation and fishing
Send what the boat is, what you want done and where it lives. Bill calls back to set a time.
- The boat. Make, length, and the year if you know it.
- The job. What you want done, or what stopped working.
- Where it lives. Dock, marina, dry stack or trailer, and the town.
Quicker on the phone: (910) 200-8617
Questions about navigation and fishing
Which brands do you install?
Garmin, Simrad, Furuno, Starlink, FLIR, Icom, Airmar and the rest of the list on the home page: Shakespeare, Jabsco, Shurflo, Lenco, Bennett, Ancor, Lewmar, Fusion, JL Audio, Lumitec, Black Oak, Lumishore, Rule and Attwood. If you own gear from another maker, ask.
Can you fit a full new dash on an older boat?
Usually, yes. A dash refit means a new panel cut for the displays and switches you actually use, with the old holes gone. Bill keeps materials such as carbon fiber and Starboard to make new dashes that cover the old holes. It is one of the most common jobs Kane Marine does.
What is NMEA 2000 and do I need it?
It is the network that lets your engine, GPS, sonar, autopilot and displays share data on one cable. If you want engine data on your plotter or one screen to show what another sees, you need it, and it has to be built right to be reliable.
Can you add radar to a boat that has never had it?
Usually, yes. Radar needs a mount with a clear sweep, a display that supports it and a power circuit of its own. On a center console that means a hardtop, T-top or an arch; Bill looks at the boat first and says what will fit before anything is ordered.
Where should the transducer go?
Where it stays in clean water at speed. On most outboard boats that is the transom, placed clear of strakes, intakes and the engine, and tuned to the hull once the boat is in the water. A transducer in the wrong spot is the most common reason a new sonar reads badly.
Can I mix a new display with my old radar or sonar?
Sometimes. Displays, GPS and engine data share over NMEA 2000, but radar and sonar modules are mostly brand-specific. If the old gear is the same brand it usually connects; if not, Bill will tell you what carries over and what does not before you buy.
Do you install autopilot?
Yes. Bill installs autopilots and ties them into the chartplotter, so the boat can hold a heading or follow a route you set on the screen.
Do you install AIS so other boats can see me?
Yes, and there are two kinds. A receive-only AIS is inexpensive to add and puts the boats around you on your chartplotter, with where they are heading and whether there is a risk of collision, which matters most at night. A transceiver also sends your own position, so other boats see you. It costs a little more and is an excellent safety feature.
Do you install thermal or night-vision cameras?
Yes. FLIR thermal cameras are excellent on the water at night and fairly quick to install.
Can you move the electronics off my old boat onto my new one?
Yes, if the gear is newer. Older units are often not worth moving, so Bill will look at what you have and tell you what is worth carrying over.
Can you update the software and charts on my Garmin or Simrad?
Yes. The most important step is setting up the maker’s phone app, ActiveCaptain on a Garmin, so your phone keeps the software and charts up to date. Bill specializes in setting that up and showing you how to use it.
Other services
Something on the boat not working?
Say what it is and where the boat is. Bill will tell you what it sounds like and when he can come.