A black helm with two covered Garmin displays above a row of rocker switches

Boat wiring, dash refits and switch panels in Wilmington, NC

Kane Marine Systems does the electrical side of the boat: full dash refits with custom switch panels, trim tab installs, battery and charger setups, bus bars, fusing and the NMEA 2000 backbone that everything else hangs off. It is the work that decides whether the electronics on top of it stay reliable.

When the wiring is the job

A power panel with house and engine battery switches, a 50 amp breaker and bilge and trim tab switches
  • The dash has old holes, dead switches and gear from three owners ago.
  • Switches work sometimes, or a breaker trips for no reason you can find.
  • You want trim tabs, or the ones you have stopped responding.
  • The battery goes flat at the dock, or the electronics drop out when the engine cranks.
  • You are adding enough gear that the old panel and fusing cannot carry it.

How the electrical work goes

Power, Wiring and Switch Panels on a boat comes down to the jobs below, all of them done at the dock by Bill.

  • Map what is there

    Every circuit traced from the battery to the device before anything is cut. Boats accumulate wiring; the first job is knowing which of it still does something.

  • Build it to a standard

    Tinned marine wire sized for the load, proper fusing at the source, labeled runs, sealed connections, and grounds back to a real bus, not a screw in wet wood.

  • Finish the helm

    A new dash made from materials such as carbon fiber or Starboard, cut for the switches and displays you actually use, backlit and labeled, covering the old holes. It looks like it came from the factory, because it was planned once.

A flat white dash panel on a center console helm, with a trim tab control below itA wireless phone charging cradle and a control pad fitted flush in a console
Request a visit

Ask about power and wiring

Send what the boat is, what you want done and where it lives. Bill calls back to set a time.

  • The boat. Make, length, and the year if you know it.
  • The job. What you want done, or what stopped working.
  • Where it lives. Dock, marina, dry stack or trailer, and the town.

Quicker on the phone: (910) 200-8617

Request a visit

Bill calls you back to set a time. Calling is quicker: (910) 200-8617.

Questions about power and wiring

What is a dash refit?

A new helm panel cut for the displays and switches you actually use, with new wiring behind it. Bill makes the new dash from materials such as carbon fiber or Starboard, so it covers the old holes. It is the usual answer when a boat has had several rounds of gear added by several owners.

Do you install trim tabs?

Yes. Trim tab installs and repairs are part of the electrical work, including the switch or the auto-trim control at the helm.

Can you sort out a battery that keeps going flat?

Usually. A flat battery is most often a parasitic draw, a weak charger or a battery that has reached the end of its life, and a meter finds which. Battery and charger setups, including a separate house bank, are part of the work.

What is the difference between marine wire and regular wire?

Marine wire is tinned, so each strand is coated against corrosion, and it is sized and insulated for heat and vibration. Automotive wire corrodes from the inside in salt air and is behind a large share of the faults Bill finds. Everything he installs is tinned marine wire, fused at the source.

Should I have a separate house battery?

If you run electronics, a livewell, lights or Starlink with the engine off, yes. A house bank carries that load and the start battery stays ready to start the engine. A charger or a voltage-sensitive relay keeps both topped up, and the electronics stop dropping out when you crank.

Can you replace a breaker panel or add circuits?

Yes. Adding gear usually means the old panel and fusing cannot carry it. A new panel with labeled breakers, a bus bar for grounds and properly sized wire is a normal part of a dash refit or a standalone job.

How long does a full dash refit take?

A couple of days, or longer depending on the scope of the job.

Something on the boat not working?

Say what it is and where the boat is. Bill will tell you what it sounds like and when he can come.

Call (910) 200-8617