Boat electronics questions, answered
66 questions boat owners around Wilmington ask, with the short answer first. If yours is not here, call and ask it.
About the business
What does Kane Marine Systems do?
Kane Marine Systems installs and repairs the electronics and electrical systems on boats: chartplotters, radar, sonar, VHF, autopilot, Starlink, lighting, pumps, gauges and switch panels. It is a mobile service run by Bill Kane in the Wilmington, NC area.
Where do you work?
New Hanover County: Wilmington, Wrightsville Beach, Carolina Beach, Kure Beach and the water in between. Bill comes to the boat, at your dock, your marina or on the trailer. Call (910) 200-8617 if you are just outside that and ask.
Do you work on engines?
No. Engine work stays with your engine dealer. Kane Marine Systems does the electrical and electronic side of the boat, including the gauges and displays that show engine data.
Do you offer emergency service?
No. Hours are Monday to Friday, 8 am to 5 pm, with Saturdays by availability. Call (910) 200-8617 or send the form and Bill will schedule a visit.
Which electronics brands do you install?
Garmin, Simrad, Furuno, Starlink, FLIR and Icom. If you already own gear from another maker, ask.
Can you install Starlink on my boat?
Yes. Kane Marine Systems was one of the early Starlink installers on boats in the Wilmington area. The dish gets a proper mount, 12-volt power and a network that reaches your phones and displays.
Do you come to the boat?
Yes. Kane Marine is a mobile service. There is no shop to bring the boat to; the work is done where the boat lives.
What is the phone number for Kane Marine Systems?
(910) 200-8617. That is Bill’s number and the only number for the business.
How do I book a visit?
Call (910) 200-8617 or send the form on the contact page. Say what the boat is, where it lives and what you want done or what stopped working. Bill answers when he can, calls back when he is on a boat, and schedules a time to come out.
Do I need to buy the electronics first?
No. If you already own the gear, Bill will install it. If you have not bought it yet, call first; he will tell you what fits the boat and how you use it, so you do not buy a display or a dish that is wrong for the helm.
Do you work on sailboats, pontoons and jon boats?
Yes. The electrical and electronic side is the same work on any hull: power, wiring, displays, lights and pumps. Most of the boats Kane Marine sees are center consoles and bay boats, but the type of boat does not change whether Bill can help.
Can you work on the boat while it is on the trailer or in dry storage?
Yes. Bill is fully insured, so he can work almost anywhere: on the trailer in your driveway, at a dry stack, in a marina slip or at a private dock. Sonar tuning needs the boat in the water, so that part happens at the end once the boat is launched.
Is Kane Marine Systems insured?
Yes. Bill is fully insured, which is why he can work at marinas and dry stacks as well as at private docks.
How do I know whether a problem is electronics or engine?
If the engine itself runs rough, stalls or will not start, it is the engine dealer. If a gauge, a display, a pump, a light or a switch is the problem, or the electronics drop out when the engine cranks, that is electrical and is worth a call to Bill.
I just bought a used boat. What should I upgrade first?
The safety equipment first, then the fishing equipment.
Do you give a quote over the phone, or do you need to see the boat?
Usually Bill needs to see the boat first, but for many jobs he can give you a general idea on the phone.
What should I have ready before you come out?
Have the boat uncovered and the access points clear of gear, so Bill can get straight to work.
How far ahead should I book?
Not far. Bill can usually get to you quickly, because he does not overbook.
Do you stand behind your installs?
Yes. If something Bill installed does not work and it is something he missed, there is no charge for the service visit.
Navigation and Fishing Electronics
Which brands do you install?
Garmin, Simrad, Furuno, Starlink, FLIR, Icom, Airmar and the rest of the list on the home page: Shakespeare, Jabsco, Shurflo, Lenco, Bennett, Ancor, Lewmar, Fusion, JL Audio, Lumitec, Black Oak, Lumishore, Rule and Attwood. If you own gear from another maker, ask.
Can you fit a full new dash on an older boat?
Usually, yes. A dash refit means a new panel cut for the displays and switches you actually use, with the old holes gone. Bill keeps materials such as carbon fiber and Starboard to make new dashes that cover the old holes. It is one of the most common jobs Kane Marine does.
What is NMEA 2000 and do I need it?
It is the network that lets your engine, GPS, sonar, autopilot and displays share data on one cable. If you want engine data on your plotter or one screen to show what another sees, you need it, and it has to be built right to be reliable.
Can you add radar to a boat that has never had it?
Usually, yes. Radar needs a mount with a clear sweep, a display that supports it and a power circuit of its own. On a center console that means a hardtop, T-top or an arch; Bill looks at the boat first and says what will fit before anything is ordered.
Where should the transducer go?
Where it stays in clean water at speed. On most outboard boats that is the transom, placed clear of strakes, intakes and the engine, and tuned to the hull once the boat is in the water. A transducer in the wrong spot is the most common reason a new sonar reads badly.
Can I mix a new display with my old radar or sonar?
Sometimes. Displays, GPS and engine data share over NMEA 2000, but radar and sonar modules are mostly brand-specific. If the old gear is the same brand it usually connects; if not, Bill will tell you what carries over and what does not before you buy.
Do you install autopilot?
Yes. Bill installs autopilots and ties them into the chartplotter, so the boat can hold a heading or follow a route you set on the screen.
Do you install AIS so other boats can see me?
Yes, and there are two kinds. A receive-only AIS is inexpensive to add and puts the boats around you on your chartplotter, with where they are heading and whether there is a risk of collision, which matters most at night. A transceiver also sends your own position, so other boats see you. It costs a little more and is an excellent safety feature.
Do you install thermal or night-vision cameras?
Yes. FLIR thermal cameras are excellent on the water at night and fairly quick to install.
Can you move the electronics off my old boat onto my new one?
Yes, if the gear is newer. Older units are often not worth moving, so Bill will look at what you have and tell you what is worth carrying over.
Can you update the software and charts on my Garmin or Simrad?
Yes. The most important step is setting up the maker’s phone app, ActiveCaptain on a Garmin, so your phone keeps the software and charts up to date. Bill specializes in setting that up and showing you how to use it.
Starlink Installation
Does Starlink work offshore?
Yes, with the right plan. Starlink sells plans that cover coastal and open water; the standard residential plan does not. Which plan you need depends on how far out you go. Bill can explain the options, and the subscription stays in your name.
Which Starlink hardware works on a boat?
The flat high-performance dish is built for vehicles and boats and holds a connection while moving. The Mini is small, runs on 12 volts and also works in motion. The standard dish is meant for a fixed spot, so it suits the dock or anchor. Ask before buying a kit; the right one depends on how you use the boat.
Do I need an inverter to run Starlink on a boat?
No. Starlink is now made in a 12-volt system, so the inverter is no longer needed. The dish runs from the boat’s own power on a fused circuit, which makes it a good fit for smaller boats.
Where does the Starlink dish mount on a center console?
On the hardtop or T-top, on a radar arch, or on its own pole. It needs an open view of the sky and a spot clear of the radar beam, outriggers and antennas. Bill picks the spot with you on the boat, because every top is different.
Can Starlink feed weather to my chartplotter?
Yes, on displays that take an internet connection. Once the boat has Wi-Fi from the Starlink router, a compatible chartplotter can pull live weather, radar overlays and software updates over it. Bill sets that up as part of the install.
How much power does Starlink use on a boat?
Enough to matter at anchor. It depends on the dish: Starlink lists the Mini at roughly 20 to 40 watts and the flat high-performance dish at roughly 110 to 150 watts, so at 12 volts that is from about 2 amps to over 10, all day. That adds up without the engine running. A proper install puts it on its own fused circuit so you can switch it off, and a house battery or charger setup keeps it from draining the start battery.
How long does a Starlink install take?
Anywhere from two hours to a full day. It depends on the size of the boat and how easy it is to get to the wire channels.
If my Starlink stops connecting, do you come back out?
Yes. Call Bill and he will come back to the boat and sort it.
Should I take the Starlink dish off before a hurricane or a long haul-out?
No. The Starlink is permanently mounted and stands up to high winds, so it stays on the boat.
Diagnostics and Repair
Do you work on engines?
No. Kane Marine Systems handles the electrical and electronic systems on the boat. For an engine problem, call your outboard or inboard dealer. If a gauge or engine display is the issue, that is often electronics and is worth a call.
Do you do emergency or after-hours calls?
No. Hours are Monday to Friday, 8 am to 5 pm, with Saturdays by availability. Call or send the form and Bill will schedule the visit.
Why do my electronics reboot when the engine starts?
Starting the engine pulls the battery voltage down for a moment. If the electronics share that battery, or a ground is weak, they drop out. The fix is usually a proper house battery setup, a voltage-sensitive relay or a corrected ground, not new electronics.
My livewell pump hums but does not pump. Is it dead?
Probably not. A pump that hums is getting power; the impeller is jammed with a shell or grass, or the pump has lost its prime on the trailer. A pump that does nothing at all is usually a fuse, a switch or a corroded connector, and a meter at the pump tells which in a minute.
Why does my fuel gauge read wrong?
Most often the sender in the tank has worn or corroded, or the ground for the gauge is bad. The gauge itself fails least often. Bill tests the sender and the wiring before anything is replaced, because a new gauge on a bad sender reads just as wrong.
Can you fix wiring that someone else did?
Yes. A lot of the repair work is undoing an earlier shortcut: automotive wire, twisted connections, a ground to a screw in wet wood. Bill traces the circuit, replaces what is wrong with marine-rated parts and seals it so it stays fixed.
What is the most common electrical problem on boats around Wilmington?
Pumps and switches. Bilge pumps, macerator pumps and switches are what go out most often.
How do I keep my electronics from corroding in salt air?
Cover them. Keeping the displays and the helm covered whenever the boat is not in use keeps salt air and spray off the screens and plugs.
Power, Wiring and Switch Panels
What is a dash refit?
A new helm panel cut for the displays and switches you actually use, with new wiring behind it. Bill makes the new dash from materials such as carbon fiber or Starboard, so it covers the old holes. It is the usual answer when a boat has had several rounds of gear added by several owners.
Do you install trim tabs?
Yes. Trim tab installs and repairs are part of the electrical work, including the switch or the auto-trim control at the helm.
Can you sort out a battery that keeps going flat?
Usually. A flat battery is most often a parasitic draw, a weak charger or a battery that has reached the end of its life, and a meter finds which. Battery and charger setups, including a separate house bank, are part of the work.
What is the difference between marine wire and regular wire?
Marine wire is tinned, so each strand is coated against corrosion, and it is sized and insulated for heat and vibration. Automotive wire corrodes from the inside in salt air and is behind a large share of the faults Bill finds. Everything he installs is tinned marine wire, fused at the source.
Should I have a separate house battery?
If you run electronics, a livewell, lights or Starlink with the engine off, yes. A house bank carries that load and the start battery stays ready to start the engine. A charger or a voltage-sensitive relay keeps both topped up, and the electronics stop dropping out when you crank.
Can you replace a breaker panel or add circuits?
Yes. Adding gear usually means the old panel and fusing cannot carry it. A new panel with labeled breakers, a bus bar for grounds and properly sized wire is a normal part of a dash refit or a standalone job.
How long does a full dash refit take?
A couple of days, or longer depending on the scope of the job.
Boat Lighting
Which lights does a boat have to show at night?
Underway, a powerboat needs red and green sidelights and a white light visible all around, either one all-round light or a masthead light plus a stern light. At anchor it needs the white all-round light. A dead light is unsafe and a ticket.
Why do my lights only work sometimes?
Corrosion in a socket, a connector or a ground. Water gets in, the contact goes intermittent, and the light works until the boat gets wet. The fix is cleaning or replacing the connection and sealing it properly.
Do you install accent lighting and light bars?
Yes. Bill installs accent lighting in full color, and light bars, which are excellent for night navigation.
Do you do underwater lights?
Ask. Call Bill and describe what you want on the boat; he will tell you whether it is something he does.
Are LED navigation lights worth it?
Yes. Marine-rated LED fixtures draw a fraction of the power, last longer and are sealed better than the incandescent lights they replace. The one rule is to buy a fixture certified for navigation use; a cheap LED that is not certified can be the wrong color or brightness and still fails the rules.
Can you add courtesy or cockpit lighting to an older boat?
Yes. Courtesy, cockpit and spreader lights can be added to almost any boat. The work is running sealed wire to each fixture, fusing the circuit properly and putting the switch or dimmer where you can reach it at the helm.
Why did both sidelights go out at the same time?
One shared fault. Both sidelights usually run on one circuit and one ground at the bow, so a corroded ground, a broken wire or a blown fuse takes both out together. That is good news: it is one repair, not two fixtures.
Packages
Is a package a fixed list or can I change it?
A starting point. Each package is a job owners ask for by name, and Bill fits it to your boat and to how you use it. The package is there so the conversation starts somewhere.
How is a package priced?
By phone or at the dock, after Bill has seen the boat. The cost depends on the gear you choose, what the boat can hold and what the existing wiring is like, so no price is published for a package.
Do you supply the gear or do I buy it?
Either. If you already own the gear, Bill installs it. If you have not bought it yet, he will say what fits the boat before you spend the money.
Can I combine packages?
Yes. Starlink, lighting and audio can be planned together, and it is easier to plan the mounts, the power and the wiring once than to add each job separately.
Why is there a package just for bilge pumps?
Because bilge pumps and their switches are among the things that go out most often on boats around Wilmington, and a pump that does not run is found at the worst time. The package is an inspection first, then the repair of whatever it turns up.
Question not here?
Ask it on the phone. It is quicker.